{"id":495,"date":"2018-07-13T11:12:19","date_gmt":"2018-07-13T11:12:19","guid":{"rendered":"https:\/\/www.bcta.group\/attma\/?page_id=495"},"modified":"2025-02-10T08:38:06","modified_gmt":"2025-02-10T08:38:06","slug":"new-zealand","status":"publish","type":"page","link":"https:\/\/www.bcta.group\/attma\/air-tightness-testers-members\/air-tightness-testers\/new-zealand\/","title":{"rendered":"Registered Air Tightness Testers \u2013 New Zealand"},"content":{"rendered":"\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t
\n\t\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Registered Air Tightness Testers - New Zealand<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

<\/p>\n

All members of ATTMA are independently audited and certified, with a scope covering air tightness testing to the ATTMA Technical Standards (TSL1 &\/or TSL2) and BS EN:13829 (2001), demonstrating knowledge and understanding, which enables them to test both commercial and domestic developments in accordance with relevant building regulations.<\/p>\n

<\/p>\n

The List of Members is shown below:<\/strong><\/p>\n

<\/p>\n

\n\n\n\n\n\n\n\n\n\n\n\n
EA Calculator Only<\/strong><\/td>\nAuthorised to carry out Envelope Area and Volume calculations but is not authorised to test<\/td>\n<\/tr>\n
Level 1<\/strong><\/td>\nAir tightness tester able to test dwellings and non-dwellings up to 4000m\u00b3 gross envelope volume, tested as a single entity with a single blower door fan.<\/td>\n<\/tr>\n
Level 2<\/strong><\/td>\nAir tightness tester able to test both Level 1 and large buildings up to 80,000m2 external envelope area and\/or up to 15 storeys tall. Level 2 testers are able to test buildings defined in Level 1. NOTE – All Level 2 testers are required to have at least one candidate that has the ‘+EA’ level.<\/td>\n<\/tr>\n
Level 3<\/strong><\/td>\nTesters who have been assessed for a higher level of expertise can test Large, Complicated and High Rise (LCHR), phased and zonal hand-over buildings. Level 3 testers are able to test buildings as defined in Level 1 and 2.<\/td>\n<\/tr>\n
Suspended<\/strong><\/td>\nTesters who have been temporarily removed from the scheme for failure to comply with the scheme rules or companies that have failed to pay the scheme fees. These companies are NOT authorised to test under the ATTMA scheme.<\/td>\n<\/tr>\n
Removed<\/strong><\/td>\nTesters have been removed from the scheme<\/td>\n<\/tr>\n
Withdrawn<\/strong><\/td>\nTesters have voluntarily withdrawn from the scheme<\/td>\n<\/tr>\n
+EA<\/strong><\/td>\nTesters with +EA are competent to carry out envelope area calculations to Level 2 \/ 3 on behalf of their business. Companies cannot operate at Level 2 or 3 without either an EA Calculator or an engineer with +EA attached to their status.<\/td>\n<\/tr>\n
Provisional Member (International Only)<\/strong><\/td>\nProvisional Members are members that have been desktop audited but have not been physically audited. This only applies to international members where audits cannot always be completed immediately.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>Any queries regarding current membership status should be directed to Barry Cope (ATTMA Scheme Manager) to manager@attma.org.<\/span><\/figure>\n

<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

\n\t\n \n \n
Company<\/th>\n Head Office<\/th>\n Mostly Tests In<\/th>\n Tester<\/th>\n ATTMA No.<\/th>\n Level 1<\/th>\n\t\t\t\tLevel 2<\/th>\n\t\t\t\tEA<\/th>\n\t\t\t\tPH<\/th>\n\t\t\t\t\n\t\t\t\tStatus<\/th>\n <\/tr>\n <\/thead>\n\n <\/table>\n\n\n